Efficient adsorption of rhodamine B using synthesized Mg-Al hydrotalcite/ sodium carboxymethylcellulose/ sodium alginate hydrogel spheres: Performance and mechanistic analysis.

In this study, the sodium dodecyl sulfate intercalated modified magnesium-aluminum hydrotalcite/sodium alginate/sodium carboxymethylcellulose (modified LDHs/SA/CMC) composite gel spheres were synthesized and their efficacies in adsorbing the cationic dye rhodamine B (RhB) from aqueous solutions were evaluated. The effects of adsorption time, pH and temperature on the adsorption of RhB by spheres were investigated. Remarkably, the modified LDHs/SA/CMC gel spheres achieved adsorption equilibrium after 600 min at 25 °C, and the removal rate of RhB at 60 mg/L reached 91.49 % with the maximum adsorption capacity of 59.64 mg/g. The gel spheres maintained over 80 % efficacy across four adsorption cycles. Kinetic and isotherm analyses revealed that the adsorption of RhB conformed to the secondary kinetic model and the Langmuir isotherm, indicating a spontaneous and exothermic nature of the adsorption process. The adsorption mechanisms of modified LDHs/SA/CMC gel spheres on RhB dyes include electrostatic adsorption, hydrogen bonding and hydrophobic interactions. In conclusion, modified LDHs/SA/CMC gel sphere is a green, simple, recyclable and efficient adsorbent, which is expected to be widely used for the treatment of cationic dye wastewater.

Research on the purification effect of major pollutants in water by modular constructed wetlands with different filler combinations.

Constructed wetland systems have been widely used in China due to their advantages of good treatment effect, low cost and environmental friendliness. However, traditional constructed wetlands have challenges in application such as deactivation due to filler clogging, difficulty in filler replacement and low adaptability. To address the above problems, this research proposes a modular filler design constructed wetland based on the concept of assembly construction, which can quickly replace the clogged filler without destroying the overall structure of the wetland. Four commonly used fillers were selected and applied to the pilot system of the assembled constructed wetland in this study, in order to investigate the purification effect of the constructed wetland system with different filler module combinations (CW1, CW2, CW3) on the simulated wastewater. The results showed that the filler combination CW1 was the best for the removal of NH4+-N, and for TP and COD, CW2 has the best removal effect. Therefore, the assembled constructed wetland is adjustable and substantially reduces the maintenance cost, which provides technical guidance for its application in engineering.

GB12-09, a bispecific antibody targeting IL4Rα and IL31Rα for atopic dermatitis therapy.

Atopic dermatitis (AD) is a chronic inflammatory skin condition characterized by dysregulated immune responses. The key mediators of AD pathogenesis are T helper 2 (TH2) cells and TH2 cytokines. Targeting interleukin 4 (IL4), IL13 or IL31 has become a pivotal focus in both research and clinical treatments for AD. However, the need remains pressing for the development of a more effective and safer therapy, as the current approaches often yield low response rates and adverse effects. In response to this challenge, we have engineered a immunoglobulin G-single-chain fragment variable (scFv) format bispecific antibody (Ab) designed to concurrently target IL4R and IL31R. Our innovative design involved sequence optimization of VL-VH and the introduction of disulfide bond (VH44-VL100) within the IL31Rα Ab scFv region to stabilize the scFv structure. Our bispecific Ab efficiently inhibited the IL4/IL13/IL31 signaling pathways in vitro and reduced serum immunoglobulin E and IL31 levels in vivo. Consequently, this intervention led to improved inflammation profiles and notable amelioration of AD symptoms. This research highlighted a novel approach to AD therapy by employing bispecific Ab targeting IL4Rα and IL31Rα with potent efficacy.

Therapeutic Drug Monitoring of Voriconazole in Patients with End-Stage Liver Disease.

BACKGROUND: This study aimed to identify the factors that influence voriconazole (VCZ) plasma concentrations and optimize the doses of VCZ in patients with end-stage liver disease (ESLD). METHODS: Patients with ESLD who received a VCZ maintenance dose of 100 mg twice daily (group A, n = 57) or the VCZ maintenance dose of 50 mg twice daily (group B, n = 37), orally or intravenously, were enrolled in this study. Trough plasma concentrations (Cmin) of VCZ between 1 and 5 mg/L were considered within the therapeutic target range. RESULTS: The VCZ Cmin was determined in 94 patients with ESLD. The VCZ Cmin of patients in group A was remarkably higher than those in group B (4.85 ± 2.53 mg/L vs 2.75 ± 1.40 mg/L; P < 0.001). Compared with group A, fewer patients in group B had VCZ Cmin outside the therapeutic target (23/57 vs. 6/37, P = 0.021). Univariate and multivariate analyses suggested that both body weight and Model for End-Stage Liver Disease scores were closely associated with the VCZ Cmin in group B. CONCLUSIONS: These data indicate that dose optimization based on body weight and Model for End-Stage Liver Disease scores is required to strike an efficacy-safety balance during VCZ treatment in patients with ESLD.

Efficacy and safety of chloral hydrate in auditory brainstem response test: A systematic review and single-arm meta-analysis.

OBJECTIVES: To evaluate the safety and efficacy of chloral hydrate in auditory brainstem response (ABR) tests. SETTING AND DESIGN: In this study, the authors systematically searched both English (Embase, PubMed, and Web of Science) and Chinese (Chinese National Knowledge Infrastructure, Wanfang Data, and VIP Chinese Science) databases. Two authors independently performed data extraction and quality assessment. The pooled sedation failure rate and the pooled incidence of adverse events were calculated via a random-effects model. Sensitivity and subgroup analyses were performed to explore the sources of heterogeneity, and the PRISMA guideline was followed. PARTICIPANTS: Patients with ABR tests receiving chloral hydrate sedation. MAIN OUTCOME MEASURES: The pooled sedation failure rate and the pooled incidence of adverse events. RESULTS: A total of 23 clinical studies were included in the final analysis. The pooled sedation failure rate of patients who received chloral hydrate sedation before ABR examination was 10.0% [95% confidence interval (CI) (6.7%, 15.0%), I2 = 95%, p < .01]. There were significant differences in the prevalence of sedation failure between sample sizes greater than 200 and those less than or equal to 200 (5.6% vs. 19.6%, p < .01) and between the studies that reported sleep deprivation and those that did not report sleep deprivation (7.1% vs. 18.9%, p < .01). The pooled incidence of adverse events was 10.32% [95% CI (5.83%, 14.82%), I2 = 98.1%, p < .01]. CONCLUSIONS: Chloral hydrate has a high rate of sedation failure, adverse events, and potential carcinogenicity. Therefore, replacing its use in ABR tests with safer and more effective sedatives is warranted.

Removal of sulfamethoxazole and Cu, Cd compound pollution by arbuscular mycorrhizal fungi enhanced vertical flow constructed wetlands.

The combined pollution of antibiotics and heavy metals (HMs) has a serious impact on the water ecological environment. Previous researches mainly focused on the removal of antibiotics or HMs as single pollutants, with limited investigation into the treatment efficiencies and underlying mechanisms associated with their co-occurring pollution. In this study, 16 micro vertical flow constructed wetlands (MVFCWs) were constructed to treat composite wastewater consisting of sulfamethoxazole (SMX), copper (Cu) and cadmium (Cd), involving two different inoculation treatments (arbuscular mycorrhizal fungi (AMF) inoculated and uninoculated) and eight kinds of pollutant exposure (Control Check (CK), SMX, Cu, Cd, SMX + Cu, SMX + Cd, Cu + Cd, SMX + Cu + Cd). The findings of this study demonstrated that the inoculation of AMF in MVFCWs resulted in removal efficiencies of SMX, Cu, and Cd ranging from 18.70% to 80.52%, 75.18% to 96.61%, and 40.50% to 89.23%, respectively. Cu and CuCd promoted the degradation of SMX in the early stage and inhibited the degradation of SMX in the later stage. Cd did not demonstrate a comparable promotive impact on SMX degradation, and its addition hindered Cu removal. However, comparatively, the presence of Cu exerted a more pronounced inhibitory effect on Cd removal. Furthermore, the addition of Cu augmented the abundances of Proteobacteria, Bacteroidetes (at the phylum level) and Rhodobacter, Lacunisphaera and Flavobacterium (at the genus level), and Cu exposure showed a substantially stronger influence on the microbial community than that of Cd and SMX. AMF might confer protection to plants against HMs and antibiotics by enriching Nakamurella and Lacunisphaera. These findings proved that AMF-C. indica MVFCW was a promising system, and the inoculation of AMF effectively enhanced the simultaneous removal of compound pollution.

Arbuscular mycorrhizal fungi enhanced the drinking water treatment residue-based vertical flow constructed wetlands on the purification of arsenic-containing wastewater.

Arsenic (As) is a toxic metalloid that poses a potential risk to the environment and human health. In this study, drinking water treatment residue (DWTR) and ceramsite-based vertical flow constructed wetlands (VFCWs) were built to purify As-containing wastewater. As a method of bioaugmentation, arbuscular mycorrhizal fungi (AMF) was inoculated to Pteris vittata roots to enhance the As removal of the VFCWs. The results showed that the As removal rates reached 87.82-94.29% (DWTR) and 33.28-58.66% (ceramsite). DWTR and P. vittata contributed 64.33-72.07% and 7.57-29% to the removal of As, while AMF inoculation intensified the As accumulation effect of P. vittata. Proteobacteria, the main As3+ oxidizing bacteria in the aquatic systems, dominated the microbial community, occupying 72.41 ± 7.76%. AMF inoculation increased As-related functional genes abundance in DWTR-based wetlands and provided a reliable means of arsenic resistance in wetlands. These findings indicated that the DWTR-based VFCWs with AMF inoculated P. vittata had a great purification effect on As-containing wastewater, providing a theoretical basis for the application of DWTR and AMF for As removal in constructed wetlands.

Subintimal recanalization for non-acute occlusion of intracranial vertebral artery in an emergency endovascular procedure: A case report.

BACKGROUND: Endovascular recanalization of non-acute intracranial artery occlusion is technically difficult, particularly when the microwire enters the subintima. Although the subintimal tracking and re-entry technique has been well established in the endovascular treatment of coronary artery occlusion, there is limited experience with its use in intracranial occlusion due to anatomical variations and a lack of dedicated devices. CASE SUMMARY: A 74-year-old man was admitted to the hospital two days after experiencing acute weakness in both lower extremities, poor speech, and dizziness. After admission, imaging revealed acute ischemic stroke and non-acute occlusion of bilateral intracranial vertebral arteries (ICVAs). On the fourth day of admission, the patient's condition deteriorated and an emergency endovascular recanalization of the left ICVA was performed. During this procedure, a microwire was advanced in the subintima of the vessel wall and successfully reentered the distal true lumen. Two stents were implanted in the subintima. The patient's Modified Rankin Scale was 1 at three months postoperatively. CONCLUSION: We present a technical case of subintimal recanalization for non-acute ICVA occlusion in an emergency endovascular procedure. However, we emphasize the necessity for caution when applying the subintimal tracking approach in intracranial occlusion due to the significant dangers involved.

Pollutants removal and connections among sludge properties, metabolism potential and microbial characteristics in aerobic granular sequencing batch reactor for petrochemical wastewater treatment.

Petrochemical wastewater contains inhibitory compounds such as aromatics that are toxic to microorganisms during biological treatment. The compact and layered structure and the high amount of extracellular polymeric substances (EPS) in aerobic granular sludge (AGS) can contribute to protecting microorganisms from the harsh environment. This study evaluated the changes in the granule properties, pollutants removal, microbial metabolic potential and molecular microbial characteristics of the AGS process for petrochemical wastewater treatment. Granules treating petrochemical wastewater had a higher SVI30/SVI5 value (0.94) than that treating synthetic wastewater. An increase in bioactivity and EPS secretion with higher bio-polymer composition, specifically the functional groups such as hydroxyl, alkoxy and amino in protein, was observed, which promoted biomass aggregation. The granules also had more than 2-fold higher specific oxygen utilization rate. The AGS-SBR process obtained an average COD removal of 93% during petrochemical wastewater treatment and an effluent bCOD of below 1 mg L-1. No obvious inhibition of nitrification and denitrification activity was observed in the processes attributed to the layered structure of AGS. The average effluent NH4+-N of 5.0 mg L-1 was obtained and TN removal efficiencies of over 80.0% was achieved. Molecular microbial analysis showed that abundant functional genera Stenotrophomonas and Pseudoxanthomonas contributed to the degradation of aromatics and other petroleum organic pollutants. They were enriched with the variation of group behavior while metabolisms of amino acids and carboxylic acids by the relevant functional genera (e.g., Cytophagia) were significantly inhibited. The enrichment of Flavobacterium and Thermomonas promoted nitrification and denitrification, respectively. This research revealed the rapid start-up, enhanced granule structural strength, high inhibition resistance and considerable performance of AGS-SBR for petrochemical wastewater treatment.

Performances and mechanisms of simultaneous removal of nitrate and phosphate by biofilter assembled with sponge iron/copper and corn cobs.

Sponge iron (SI) is a potential material for removing nitrate and phosphate from water. We decorated the SI with copper (Cu) to enhance its removal performance. To gain insight into the nitrate and phosphate removal utilizing SI/Cu and microbial coupling systems, three biofilters filled with corn cob (CC), corn cob + sponge iron (CS) and corn cob + sponge iron/copper (CSCu) were constructed. The results showed that the effluent NO3--N and PO43--P concentrations of CSCu remained consistently below 1 and 0.1 mg/L. The introduction of SI/Cu led to the enrichment of the Dechloromonas genus, making it the dominant microbial group, occupying 42.65% of the effective sequences. Modification of SI with Cu increased nitrogen cycle-related functional genes abundance in CSCu, with a 634% increase in nirS compared to CS. These findings proved that SI/Cu was a promising material, providing an approach to concomitantly removing nitrate and phosphate.

Zeolite/ZnAl-layer double hydroxides with different Zn/Al ratios and intercalated anions as the substrate of constructed wetlands: synthesis, characterization and purification effect of Hexavalent chromium.

The study aimed to synthesize novel zeolite substrates modified with four types of ZnAl-LDHs including Cl-LDHs(1:1), Cl-LDHs(3:1), CO3-LDHs(1:1), and CO3-LDHs(3:1); investigate Cr(VI) removal efficiencies in lab-scale constructed wetlands (CWs); and explore the effect of different Zn/Al ratios and intercalated anions on the removal efficiencies of Cr(VI) by modified zeolite. Different ZnAl-LDHs were prepared by co-precipitation method and coated onto the surface of original zeolite. Field emission scanning electron microscope and energy dispersive spectrometer were used to analyze physicochemical properties of zeolite/ZnAl-LDHs. Obtained results confirmed the successful LDHs-coating modification. The results of both X-ray diffraction and Fourier transform infrared suggested that the typical diffraction peak and functional groups of ZnAl-LDHs were detected in modified zeolites, and the peak of CO32- in CO3-LDHs at 1362 cm-1 was stronger and sharper than Cl-LDHs. It could be demonstrated by above results that the synthesis crystallinity and coating effect of CO3-LDHs was better than Cl-LDHs. Furthermore, it could be found that under the condition of same intercalated anion, LDHs with metal molar ratio of 1:1 had better crystallinity than LDHs with metal molar ratio of 3: 1. Subsequent determination of the removal performance of Cr(VI) by purification experiments revealed that zeolite/Cl-LDHs(3:1) showed the best Cr(VI) removal performance, and the removal rate of Cr(VI) was improved by 32.81% compared with the original zeolite, which suggested that could be an efficient substrate of CWs for Cr(VI) removal. The high crystallinity indicated that the structure of LDHs was stable and it was difficult to remove Cr(VI) by ion exchange. The above explained why the Cr(VI) removal efficiency by zeolite/Cl-LDHs is superior to that by zeolite/CO3-LDHs under the condition of same metal molar ratio. With the increase of metal molar ratio, the charge density of LDHs layers and intercalated anion increased, thus enhancing the electrostatic attraction of LDHs layers to Cr(VI) and the interlayer anion exchange capacity. However, the effect of charge density on Cr(VI) removal efficiency may be greater than crystallinity on removal efficiency, which could be responsible for the fact that zeolite/ZnAl-LDHs(3:1) had better Cr(VI) removal efficiency than zeolite/ZnAl-LDHs(1:1) under the condition of same intercalated anion.

Developmental and Reproductive Impacts of Four Bisphenols in Daphnia magna.

Bisphenol A (BPA) is a typical endocrine-disrupting chemical (EDC) used worldwide. Considering its adverse effects, BPA has been banned or strictly restricted in some nations, and many analogs have been introduced to the market. In this study, we selected three representative substitutes, BPS, BPF, and BPAF, along with BPA, to assess the developmental and reproductive effects on Daphnia magna. The F0 generation was exposed to bisphenols (BPs) at an environmentally relevant concentration (100 µg/L) for 21 d; then the embryo spawn at day 21 was collected. Behavior traits, the activity of antioxidant enzymes, and gene transcription were evaluated at three developmental stages (days 7, 14, and 21). Notably, body length, heart rate, and thoracic limb beating were significantly decreased, and D. magna behaved more sluggishly in the exposed group. Moreover, exposure to BPs significantly increased the antioxidant enzymatic activities, which indicated that BPs activated the antioxidant defense system. Additionally, gene expression indicated intergenerational effects in larvae, particularly in the BPAF group. In conclusion, BPA analogs such as BPF and BPAF showed similar or stronger reproductive and developmental toxicity than BPA in D. magna. These findings collectively deepen our understanding of the toxicity of BPA analogs and provide empirical evidence for screening safe alternatives to BPA.

Soil Quality Assessment in Farmland of a Rapidly Industrializing Area in the Yangtze Delta, China.

The comprehensive quality assessment of farmland soil is critical for agricultural production and soil ecological protection. Currently, there is no systematic method for conducting a comprehensive quality assessment of farmland soil; subsequently, as the most developed economic area in China, the comprehensive quality assessment of farmland soil in the Yangtze River Delta is lacking. We chose the farmland soil of Suzhou city as the research object. The soil fertility index (SFI) and soil environment index (SEI) were calculated with the membership function and Nemerow index. Finally, the comprehensive assessment of soil quality was achieved with the TOPSIS model. The results showed that the average values of soil pH, SOM, TN, AHN, AP, and AK were 6.44 (slightly acidic), 28.17 g/kg (medium), 1.63 g/kg (rich), 118.16 mg/kg (medium), 38.31 mg/kg (rich), and 160.63 mg/kg (rich), respectively. For the concentrations of heavy metals, including Cr, Ni, Cu, Zn, Cd, and Pb, in 122 soil samples, the percentages exceeding the background values of Jiangsu province were 5.74%, 8.20%, 8.20%, 10.66%, 86.07%, and 84.43%, respectively. Cd and Pb were the main heavy metal pollutants on farmlands. The soil samples with SFI values below the medium level (SFI < 0.6) accounted for 44.26%, and samples with SEI values below the medium level (SEI < 0.6) accounted for 13.12%. The values of the soil quality index (SQI) ranged from 0.171 to 0.996, with an average SQI value of 0.586 (very poor-V), and approximately half of the farmland soil quality in Suzhou city needed to be further improved. In a word, this study provides a theoretical basis and scientific support for the quality assessment and rational utilization of farmland soil.

A modified receptor model for source apportionment of sediment polycyclic aromatic hydrocarbons.

Polycyclic aromatic hydrocarbons (PAHs) have become a serious threat to human health and ecological security due to their persistence and high toxicity. Lake sediments are in a relatively closed environment, so PAHs and other pollutants can be preserved for a long time. Accurate analysis of the sources of PAHs in sediments is an important prerequisite for PAH pollution control. However, the existing PAHs source resolution receptor model (the absolute principal component analysis - multilinear regression (APCA-MLR) and positive matrix factorization (PMF)) has many defects, such as great uncertainty in the process of matrix rotation. In this study, we collected sediment samples from Taihu Lake and tested their PAH content, and the existing receptor model was improved. High PAH contents were distributed in Meiliang Bay, Zhushan Bay, Gonghu Bay and areas close to the shore. "High-High" areas were distributed in Meiliang Bay, Gonghu Bay and areas close to the shore. "Low-Low" areas appeared in the central and southern parts of Taihu Lake. The results show that the improved positive matrix factorization partition computing (PMF-PC) model is significantly better than the APCA-MLR and PMF models in terms of both numerical simulation accuracy and the spatial distribution consistency of PAHs. The correlations (R2) between the measured and simulated values of low-molecular-weight PAHs (L-PAHs), high-molecular-weight PAHs (H-PAHs) and PAHs were 0.992, 0.989 and 0.993, respectively. The contributions of biomass sources, coal combustion sources and petroleum sources to PAHs in Taihu Lake sediments reached 16.7%, 31.7% and 51.6%, respectively. Fossil fuel sources were mainly concentrated in areas near the shore, and the contribution was lower in areas far from the shore. Although the algorithm still needs to be improved, the PMF-PC model may become a useful tool for the source apportionment of PAHs in sediments.

Assessing the effect of SiO2 and TiO2 nanoparticles on granule stability and microbial community shift in aerobic granular sludge process.

The widely used SiO2 and TiO2 nanoparticles (NPs) can accumulate in industrial wastewaters, thereby posing challenge to biological wastewater treatment processes. In this work, the performance of aerobic granular sludge (AGS) reactors fed with wastewater containing 50 mg L-1 SiO2 and TiO2 NPs were investigated. The results showed that the granules could resist the NPs in wastewater (no disintegration of granules was observed). SiO2 NPs had a negative effect on the settleability of granules, with the SVI30 increased by 64.5% and protein secretion decreased by 29.9%. To the contrary, the settleability of granules was improved in the presence of TiO2 NPs due to the increase of the protein secretion. Possibly because of the compact and layered structure of granules, in the presence of both types of NPs, no obvious reduction of the overall removal efficiency of organics was found, and nanoparticle-resistant strains were enriched. The overall nitrification and denitrification efficiencies were hardly affected by SiO2 NPs while significantly inhibited by TiO2 NPs. Some functional genera, such as Hyphomicrobium and Acidovorax, showed growth inhibition with TiO2 NPs, which might be responsible for the reduction of nitrification and denitrification efficiencies.

The positive effects of arbuscular mycorrhizal fungi inoculation and/or additional aeration on the purification efficiency of combined heavy metals in vertical flow constructed wetlands.

Inoculation with arbuscular mycorrhizal fungi (AMF) and additional aeration (AA), as two approaches to improve the functioning of treatment wetlands, can further promote the capacity of wetlands to purify pollutants. The extent to which, and mechanisms by which, AMF and AA purify wetlands polluted by combined heavy metals (HMs) are not well understood. In this study, the effects and mechanisms of AMF and/or AA on combined HMs removal in vertical flow constructed wetlands (VFCWs) with the Phragmites australis (reeds) were investigated at different HMs concentrations. The results showed that (1) AA improved the AMF colonization in VFCWs and AMF accumulated the combined HMs in their structures; (2) AMF inoculation and/or AA significantly promoted the reeds growth and antioxidant enzymes activities, thereby alleviating oxidative stress; (3) AMF inoculation and AA significantly enhanced the removal rates of Pb, Zn, Cu, and Cd under the stress of high combined HMs concentrations comparing to the control check (CK) treatment (autoclaved AMF inoculation and no aeration), which increased by 22.72%, 30.31%, 12.64%, and 50.22%, respectively; (4) AMF inoculation and/or AA significantly promoted the combined HMs accumulation in plant roots and substrates and altered the distribution of HMs at the subcellular level. We therefore conclude that AMF inoculation and/or AA in VFCWs improves the purification of combined HM-polluted water, and the VFCWs-reeds-AMF/AA associations exhibit great potential for application in remediation of combined HM-polluted wastewater.

The sources risk assessment combined with APCS/MLR model for potentially toxic elements in farmland of a first-tier city, China.

With the rapid economic development, potentially toxic elements (PTEs) are continuously migrating, transforming, and enriching in farmland through atmospheric deposition and other media, posing threats to food security and human health. At present, there are few quantitative studies on the health risks of PTEs sources in farmland. In this study, absolute principal component score-multiple linear regression (APCS-MLR) receptor model was used to quantify the pollution sources of PTEs in farmland in Suzhou of Yangtze River Delta Economic Zone, China. Combined with geoaccumulation index (Igeo) and health risk assessment model, the source risk of PTEs was further quantified. The results show that Cd has reached the level of unpolluted to moderate polluted (0 < Igeo < 1); the total hazard index (THI) and total carcinogenic risk (TCR) index of PTEs are acceptable for adults, but not for children (THI > 1, TCR > 1 × 10-4). The results of APCS-MLR source apportionment were industrial sources (25.65%), agricultural sources (20.00%), traffic sources (16.81%), and domestic pollution sources (9.71%). The Igeo values of all pollution sources were less than 0, and no ecological risk was caused. The contribution patterns of pollution sources to THI and TCR in adults and children are similar. Industrial pollution sources pose the greatest non-carcinogenic risk to humans, accounting for 47.35% and 47.26% of adults and children, respectively; for carcinogenic risks, domestic pollution sources contribute the most among all identified pollution sources, accounting for 27.71% and 27.73% of adults and children, respectively. In general, this study emphasizes the need to strengthen the supervision of industrial pollution sources and domestic pollution sources in the study area to reduce the health risks to children.

[Protective Effects of Akkermansia muciniphila and Amuc_1100 Protein on Rats on High-Fat Diet Combined with Streptozotocin Injection].

OBJECTIVE: To explore the protective effects of live or pasteurized Akkermansia muciniphila and Amuc_1100 protein on a rat model of diabetes mellitus induced by high-fat diet (HFD) combined with streptozotocin (STZ). METHODS: A total of 96 Sprague-Dawley (SD) rats were randomly assigned to 8 groups, including 6 experimental groups and 2 control groups, with 12 rats in each group. HFD combined with STZ injection was given to the rats to create a simulated model of the progression of diabetes mellitus type 2. In addition, the rats were treated with different doses of live or pasteurized Akkermansia muciniphila or Amuc_1100 protein by way of gavage for 8 weeks simultaneously. Plasma samples were collected to determine the level of parameters related to lipid and glucose metabolism, and inflammation mediators. Colon tissue specimens were collected for HE staining. Stool samples of the rats were collected for 16S rRNA gene sequencing. RESULTS: Compared with the HFD control group, rats in the group treated with Akkermansia muciniphila exhibited significantly lower body mass gain ( P<0.01) and lower plasma TNF-α level ( P<0.05). Administration of Akkermansia muciniphila or Amuc_1100 protein increased the number of goblet cells and mucin secretion. The ß diversity analysis of the samples showed no overall difference in the intervention groups. CONCLUSION: Oral administration of Akkermansia muciniphila can effectively ameliorate HFD-induced metabolic disorders, including body mass gain and systemic inflammation. Akkermansia muciniphila and Amuc_1100, to a certain degree, improved the gut barrier function. After eight weeks of intervention, there was no significant impact on the structure of the gut microbiota.

Microbial explanation to performance stratification along up-flow solid-phase denitrification column packed with polycaprolactone.

In this study, the fluctuating profiles of physicochemical and microbial characterizations along different filling heights of continuously up-flow solid-phase denitrification (SPD) columns packed with polycaprolactone (PCL) were investigated. It was found both the PCL filling area and non-filling area made significant contributions to treatment performance and denitrification mainly occurred near the bottom of the filling column. Nitrate displayed a high proportional removal (≥98.7%) among all the cases except the one with the lowest filling ratio (FR30) and highest NLR (3.99 ± 0.12 gN/(L·d)), while nitrite and ammonium displayed a weak accumulation in final effluents (nitrite ≤ 0.40 mg/L; ammonium ≤ 0.98 mg/L). The intensity of PCL hydrolysis in the top substrate was stronger than those in the middle or bottom. Both dissimilatory nitrate reduction to ammonium (DNRA) and microbial lysis contributed to ammonium accumulation, and nitrate was mainly removed via traditional denitrification and DNRA. JGI_0000069-P22_unclassified and Gracilibacteria_unclassified might contribute to denitrification.